Swisscom Netopia Wireless Router Workaround

Use Netopia 3357 wireless router to extend your existing network. In wireless admin expert mode settings, disable the option in LAN/WAN (LAN/WAN Turnaround). This option will disable the DSL port and enable LAN 4. Connect your LAN cable from LAN 4 to another router/network LAN port.


To update with the latest firmware from swisscom. Download the latest firmware from swisscom FTP site. ftp://ftp.bluewin.ch/support/firmware_driver/netopia/modem_router/3357-02/

Since the latest firmware 7.8.0r1, the passwords and wireless settings are no longer available for edit via the web interface on the router. However, all settings can be changed via telnet.

Connect With Telnet
Open with telnet session to the router (the address is usually 192.168.1.1).
Log in using the username and password (if not changed, then "admin" and "1234").

Call settings
Netopia-3000/XXX> configure Netopia-3000/XXX> configure

DynDNS einrichten DynDNS set up
Netopia-3000/XXX> configure Netopia-3000/XXX> configure
Netopia-3000/XXX (top)>> set dyn Netopia-3000/XXX (top)>> set dyn
dynamic-dns option (dyndns.org) [ off | dyndns.org ]: dyndns.org dynamic-dns option (dyndns.org) [off | dyndns.org]: dyndns.org
ddns-host-name (""): myhost.dyndns.org ddns-host-name (""): myhost.dyndns.org
ddns-user-name (""): myuser ddns-user-name (""): myuser
ddns-user-password(""): mypassword ddns-user-password mypassword (""):
Netopia-3000/XXX (top)>> save Netopia-3000/XXX (top)>> save

Check that everything is set up correctly:
Netopia-3000/XX (dynamic-dns)>> dyn validate Netopia-3000/XX (dynamic-dns)> validate dyn>
Validation passed! Validation passed!

Overview of input data:
Netopia-3000/X (dynamic-dns)>> dyn view Netopia 3000 / X (dynamic-dns)>> dynamic view
=============================================== ===============================================
dynamic-dns dynamic-dns
option dyndns.org option dyndns.org
ddns-host-name "myhost.homedns.org" ddns-host-name "myhost.homedns.org"
ddns-user-name "myuser" ddns-user-name "myuser"
ddns-user-password "mypassword" ddns-user-password "mypassword"

Router Password Change
Netopia-3000/XXX> configure Netopia-3000/XXX> configure
Netopia-3000/XXX (top)>> set system password admin Netopia-3000/XXX (top)>> set system password admin
Old Password Old Password
admin-password : ************ admin password: ************
New Password New Password
admin-password : **** admin-password: ****
Repeat Password Repeat Password
admin-password : **** admin-password: ****
The password has been changed. The password has been changed.
Netopia-3000/XXX (top)>> save Netopia-3000/XXX (top)>> save

WLAN settings
Netopia-3000/XXX> configure Netopia-3000/XXX> configure
Netopia-3000/XXX (top)>> set wireless Netopia-3000/XXX (top)>> set wireless

Then all the points go through and enter the desired value:
option (on) [ off | on ]: on option (on) [off | on]: on
radio_disabled (off) [ off | on ]: off radio_disabled (off) [off | on]: off
default-channel (7) [ 1 - 13 ]: 11 default-channel (7) [1 - 13]: 11
auto-channel (off) [ off | on-startup | continuous ]: off auto-channel (off) [off | on-startup | continuous]: off
network-id network-id
ssid (""): Name-des-WLAN-Netztes (""): ssid name of the wireless networked
closed-system (off) [ off | on ]: würd ich auf off lassen closed-system (off) [off | on]: I'd be off to
privacy Privacy
option (WPA-PSK) [ off | WEP | WPA-PSK | WPA-802.1x ]: WPA-PSK option (WPA-PSK) [off | WEP | WPA-PSK | WPA-802.1x]: WPA-PSK
pre-shared-key (""): ihr-Passwort-hier pre-shared-key (""): their password-here
wpa-version (all) [ all | WPA1-only | WPA2-only ]: all (wegen alten karten) wpa-version (all) [all | WPA1-only | WPA2-only]: all (because of old cards)
multi-ssid multi-ssid
option (off) [ off | on ]: off option (off) [off | on]: off
no-bridging (off) [ off | on ]: off no-bridging (off) [off | on]: off
mode (both-b-and-g) [ both-b-and-g | b-only | g-only ]: both-b-and-g mode (both-b-and-g) [both-b and-g | b-only | g-only] both-b and-g
tx-power (full) [ full | medium | fair | low | minimal ]: full tx-power (full) [full | medium | fair | low | minimal]: full
wmm wmm
option (off) [ off | on ]: off option (off) [off | on]: off

mac-auth mac-auth
option (off) [ off | on ]: off option (off) [off | on]: off
Netopia-3000/XXX (top)>> save Netopia-3000/XXX (top)>> save

Remote access off

So the router can not wait Swisscom more remote, then no settings can make in the MCC!

Netopia-3000/XXX> configure Netopia-3000/XXX> configure
Netopia-3000/XXX (top)>> set dslf-cpewan option off Netopia-3000/XXX (top)>> set dslf cpewan-off option
Netopia-3000/XXX (top)>> save Netopia-3000/XXX (top)>> save
Netopia-3000/XXX (top)>> exit Netopia-3000/XXX (top)>> exit
Netopia-3000/XXX> reboot Netopia-3000/XXX> reboot

Settings leave

Netopia-3000/XXX> exit Netopia-3000/XXX> exit

NAT default Server alias DMZ NAT default server alias DMZ

set nat-default mode default-server set nat-default mode default-server
set nat-default address {ip_address} set nat-default address {ip_address}

SOURCE

http://yene.ch/vdsl-router/

Leave a Reply

Fill in your details below or click an icon to log in:

WordPress.com Logo

You are commenting using your WordPress.com account. Log Out / Change )

Twitter picture

You are commenting using your Twitter account. Log Out / Change )

Facebook photo

You are commenting using your Facebook account. Log Out / Change )

Google+ photo

You are commenting using your Google+ account. Log Out / Change )

Connecting to %s